snow plough SRS-3L

The three-blade snow plough "SRS-3L" is mainly used in areas with less snow. It can be mounted on tractors and transporters with less weight but where high performance of snow clearing is requested. The sophisticated construction, as well as the use of high quality material result in an optimum balance of weights and maximum stability of the “SRS-3 L”.
Only high-quality fine-grained steels are used to build the "SRS-3 L", and similarly only low-wear, fully hardened high-performance steel with a hardness of 450 HB (Brinell hardness) are used for the scraping edge. The design of the “SRS-3 L”  is essentially supported by the plough's robust frame, the broad bearing surfaces of the large bolts, the robust rotating mechanism and  the three-part plough blade. This generates maximum stability with optimised weight. All bearing bolts are internally lubricated, secured against tunrning and screwed in.
The technically perfect SRS release system and the optimum rejecting of the plough shares are the result of long-time experienced development.

 

 attachment variants

 

  • attachment with coupling plate
     
  • 3-point linkage
     
  • attachment frame for wheel- and farm loaders, inclusive height adjustment
     

A detailed description of the different attachment variants can be found at the page of the coupling systems.
 

 

 

 

 

 operating principle of the SRS system

The lower swings are kept in operating position by the snow pressures, pull-back springs and guide track rollers.
If the plough hits any small obstacles, it moves upwards and slightly backwards. In case of bigger obstacles, the SRS snow plough moves completely upwards and backwards and then again back in operation position.

The towing vehicle does not need to be stopped.

For lighter snow clearing work you can remove pressure or demount seperate pull-back springs very easily. This causes the plough share to slide easily over any obstacles.

 standard equipment

 

  • plough with three blades - laterally heightened
  • SRS - plough locking
  • 4 pull back springs per plough share
  • hydraulic lateral adjustment, secured by a double shock valve
  • double acting lifting cylinders (with lowering throttle valve) - not for 3-point linkage
  • sliding plates, adjustable by pins, with crash damper
  • pendulum compensation  - lockable
  • screwed scraping edge (200 x 40 mm) from low-wear, hardened performance steel (450 HB)
  • automatic horizontal compensation in lifted position
  • big dimensioned, replaceable side deflectors
  • parking props
  • LED lighting 12/24V
  • warning flags
  • plough sided coupling plates orig. Hauer or EURO size 3, alternative 3-point linkage
  • 4 short connection hoses with coupling halves


 

 additional equipment

You can adapt the snow plough "SRS-2" optimally to your individual requirements with our additional equipment, in order to make your snow clearing work more efficient.
 

  • snow dust shield, adjustable
     
  • snow deflector - rubber
     
  • hydraulic horizontal rotation device for clearing the pavement 14° left / 14° right (additional lines or directional control valve necessary)
     
  • rubber edge GU 200 x 50mm
     
  • KÜPER scraping edge S36



 

 types + technical data

 

type / width (mm) SRS-3L 2800 SRS-3L 3000 SRS-3L 3200

clearing width with max. inclination

2470 2650 2820

plough height centre / side

850 / 1000

min. transport width with max. inclination

2610 2790 2960
min. transport width without max. inclination (max. width) 2980 3180 3380
min. vehicle width with max. inclination 2100 2280 2450
weight with coupling plate (kg) 720 733 746
weight with 3-point linkage (kg) 650 663 676

 

 


technical note

Figures and details are approximate and non-binding and change slightly depending on changes in design or construction. Pictures can deviate from the standard scope of supply.
Subject to technical changes and errors!